huangjin/AC63_BT_SDK
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
AC63_BT_SDK/apps/hid/board/br30/board_ac6373b_mouse.c

662 lines
21 KiB
C
Raw Permalink Normal View History

原始文件
2025-02-18 15:40:42 +08:00
#include "app_config.h"
#ifdef CONFIG_BOARD_AC6373B_MOUSE
#include "system/includes.h"
#include "media/includes.h"
#include "asm/sdmmc.h"
#include "asm/chargestore.h"
#include "asm/charge.h"
#include "key_event_deal.h"
#include "user_cfg.h"
/* #include "asm/lp_touch_key.h" */
#include "device/key_driver.h"
#include "asm/power/p33.h"
#include "code_switch.h"
#include "OMSensor_manage.h"
#include "asm/power_interface.h"
#define LOG_TAG_CONST BOARD
#define LOG_TAG "[BOARD]"
#define LOG_ERROR_ENABLE
#define LOG_DEBUG_ENABLE
#define LOG_INFO_ENABLE
/* #define LOG_DUMP_ENABLE */
#define LOG_CLI_ENABLE
#include "debug.h"
void board_power_init(void);
#define __this (&status_config)
/************************** KEY MSG****************************/
/*各个按键的消息设置，如果USER_CFG中设置了USE_CONFIG_KEY_SETTING为1，则会从配置文件读取对应的配置来填充改结构体*/
u8 key_table[KEY_NUM_MAX][KEY_EVENT_MAX] = {
// SHORT LONG HOLD UP DOUBLE TRIPLE
{KEY_MUSIC_PP, KEY_POWEROFF, KEY_POWEROFF_HOLD, KEY_NULL, KEY_CALL_LAST_NO, KEY_NULL}, //KEY_0
{KEY_MUSIC_NEXT, KEY_VOL_UP, KEY_VOL_UP, KEY_NULL, KEY_OPEN_SIRI, KEY_NULL}, //KEY_1
{KEY_MUSIC_PREV, KEY_VOL_DOWN, KEY_VOL_DOWN, KEY_NULL, KEY_HID_CONTROL, KEY_NULL}, //KEY_2
/* {KEY_EAR_IN, KEY_EAR_OUT, KEY_NULL, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_3 */
};
// *INDENT-OFF*
/************************** UART config****************************/
#if TCFG_UART0_ENABLE
UART0_PLATFORM_DATA_BEGIN(uart0_data)
.tx_pin = TCFG_UART0_TX_PORT, //串口打印TX引脚选择
.rx_pin = TCFG_UART0_RX_PORT, //串口打印RX引脚选择
.baudrate = TCFG_UART0_BAUDRATE, //串口波特率
.flags = UART_DEBUG, //串口用来打印需要把改参数设置为UART_DEBUG
UART0_PLATFORM_DATA_END()
#endif //TCFG_UART0_ENABLE
/************************** CHARGE config****************************/
#if TCFG_CHARGE_ENABLE
CHARGE_PLATFORM_DATA_BEGIN(charge_data)
.charge_en = TCFG_CHARGE_ENABLE, //内置充电使能
.charge_poweron_en = TCFG_CHARGE_POWERON_ENABLE, //是否支持充电开机
.charge_full_V = TCFG_CHARGE_FULL_V, //充电截止电压
.charge_full_mA = TCFG_CHARGE_FULL_MA, //充电截止电流
.charge_mA = TCFG_CHARGE_MA, //充电电流
.charge_trickle_mA = TCFG_CHARGE_TRICKLE_MA, //涓流电流
/*ldo5v拔出过滤值，过滤时间 = (filter*2 + 20)ms,ldoin<0.6V且时间大于过滤时间才认为拔出
对于充满直接从5V掉到0V的充电仓，该值必须设置成0，对于充满由5V先掉到0V之后再升压到xV的
充电仓，需要根据实际情况设置该值大小*/
.ldo5v_off_filter = 100,
.ldo5v_on_filter = 50,
.ldo5v_keep_filter = 220,
.ldo5v_pulldown_lvl = CHARGE_PULLDOWN_200K,
.ldo5v_pulldown_keep = 1,
#if !TCFG_CHARGESTORE_ENABLE
//1、对于自动升压充电舱,若充电舱需要更大的负载才能检测到插入时，请将该变量置1,并且根据需求配置下拉电阻档位
//2、对于按键升压,并且是通过上拉电阻去提供维持电压的舱,请将该变量设置1,并且根据舱的上拉配置下拉需要的电阻挡位
//3、对于常5V的舱,可将改变量设为0,省功耗
.ldo5v_pulldown_en = 1,
#else
.ldo5v_pulldown_en = 0,
#endif
CHARGE_PLATFORM_DATA_END()
#endif//TCFG_CHARGE_ENABLE
/************************** IO KEY ****************************/
#if TCFG_IOKEY_ENABLE
const struct iokey_port iokey_list[] = {
{
.connect_way = ONE_PORT_TO_LOW, //IO按键的连接方式
.key_type.one_io.port = TCFG_IOKEY_MOUSE_LK_PORT, //IO按键对应的引脚
.key_value = KEY_LK_VAL, //按键值
},
{
.connect_way = ONE_PORT_TO_LOW, //IO按键的连接方式
.key_type.one_io.port = TCFG_IOKEY_MOUSE_RK_PORT, //IO按键对应的引脚
.key_value = KEY_RK_VAL, //按键值
},
{
.connect_way = ONE_PORT_TO_LOW, //IO按键的连接方式
.key_type.one_io.port = TCFG_IOKEY_MOUSE_HK_PORT, //IO按键对应的引脚
.key_value = KEY_HK_VAL, //按键值
},
};
const struct iokey_platform_data iokey_data = {
.enable = TCFG_IOKEY_ENABLE, //是否使能IO按键
.num = ARRAY_SIZE(iokey_list), //IO按键的个数
.port = iokey_list, //IO按键参数表
};
#if MULT_KEY_ENABLE
//组合按键消息映射表
//配置注意事项:单个按键按键值需要按照顺序编号,如power:0, prev:1, next:2
//bit_value = BIT(0) | BIT(1) 指按键值为0和按键值为1的两个按键被同时按下,
//remap_value = 3指当这两个按键被同时按下后重新映射的按键值;
const struct key_remap iokey_remap_table[] = {
{.bit_value = KEY_LK_VAL | KEY_RK_VAL, .remap_value = 3},
{.bit_value = KEY_LK_VAL | KEY_HK_VAL, .remap_value = 4},
{.bit_value = KEY_RK_VAL | KEY_HK_VAL, .remap_value = 5},
};
const struct key_remap_data iokey_remap_data = {
.remap_num = ARRAY_SIZE(iokey_remap_table),
.table = iokey_remap_table,
};
#endif
#endif
/************************ OPTICAL_MOUSE_SENSOR config********************/
#if TCFG_OMSENSOR_ENABLE
#if TCFG_HAL3205_EN
OMSENSOR_PLATFORM_DATA_BEGIN(OMSensor_data)
.OMSensor_id = "hal3205",
.OMSensor_sclk_io = TCFG_OPTICAL_SENSOR_SCLK_PORT,
.OMSensor_data_io = TCFG_OPTICAL_SENSOR_DATA_PORT,
.OMSensor_int_io = TCFG_OPTICAL_SENSOR_INT_PORT,
OMSENSOR_PLATFORM_DATA_END();
#endif /* TCFG_HAL3205_EN */
#endif /* TCFG_OMSENSOR_ENABLE */
/**************************** CODE_SWITCH config************************/
#if TCFG_CODE_SWITCH_ENABLE
SW_PLATFORM_DATA_BEGIN(sw_data)
.a_phase_io = TCFG_CODE_SWITCH_A_PHASE_PORT,
.b_phase_io = TCFG_CODE_SWITCH_B_PHASE_PORT,
SW_PLATFORM_DATA_END();
#endif /* TCFG_CODE_SWITCH_ENABLE*/
/************************** AD KEY ****************************/
#if TCFG_ADKEY_ENABLE
const struct adkey_platform_data adkey_data = {
.enable = TCFG_ADKEY_ENABLE, //AD按键使能
.adkey_pin = TCFG_ADKEY_PORT, //AD按键对应引脚
.ad_channel = TCFG_ADKEY_AD_CHANNEL, //AD通道值
.extern_up_en = TCFG_ADKEY_EXTERN_UP_ENABLE, //是否使用外接上拉电阻
.ad_value = { //根据电阻算出来的电压值
TCFG_ADKEY_VOLTAGE0,
TCFG_ADKEY_VOLTAGE1,
TCFG_ADKEY_VOLTAGE2,
TCFG_ADKEY_VOLTAGE3,
TCFG_ADKEY_VOLTAGE4,
TCFG_ADKEY_VOLTAGE5,
TCFG_ADKEY_VOLTAGE6,
TCFG_ADKEY_VOLTAGE7,
TCFG_ADKEY_VOLTAGE8,
TCFG_ADKEY_VOLTAGE9,
},
.key_value = { //AD按键各个按键的键值
TCFG_ADKEY_VALUE0,
TCFG_ADKEY_VALUE1,
TCFG_ADKEY_VALUE2,
TCFG_ADKEY_VALUE3,
TCFG_ADKEY_VALUE4,
TCFG_ADKEY_VALUE5,
TCFG_ADKEY_VALUE6,
TCFG_ADKEY_VALUE7,
TCFG_ADKEY_VALUE8,
TCFG_ADKEY_VALUE9,
},
};
#endif
/************************** LOW POWER config ****************************/
const struct low_power_param power_param = {
.config = TCFG_LOWPOWER_LOWPOWER_SEL, //0：sniff时芯片不进入低功耗 1：sniff时芯片进入powerdown
.btosc_hz = TCFG_CLOCK_OSC_HZ, //外接晶振频率
.delay_us = TCFG_CLOCK_SYS_HZ / 1000000L, //提供给低功耗模块的延时(不需要需修改)
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.6V
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
.osc_type = TCFG_LOWPOWER_OSC_TYPE,
//.lpctmu_en = TCFG_LP_TOUCH_KEY_ENABLE,
.vddio_keep = 0,
};
/************************** PWR config ****************************/
struct port_wakeup port0 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = 0,
.iomap = TCFG_CODE_SWITCH_A_PHASE_PORT, //唤醒口选择
};
struct port_wakeup port1 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = 0,
.iomap = TCFG_CODE_SWITCH_B_PHASE_PORT, //唤醒口选择
};
struct port_wakeup port2 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = PORT_FLT_2ms,
.iomap = TCFG_OPTICAL_SENSOR_INT_PORT, //唤醒口选择
};
struct port_wakeup port3 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = PORT_FLT_2ms,
.iomap = TCFG_IOKEY_MOUSE_RK_PORT, //唤醒口选择
};
struct port_wakeup port4 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = PORT_FLT_2ms,
.iomap = TCFG_IOKEY_MOUSE_LK_PORT, //唤醒口选择
};
struct port_wakeup port5 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = PORT_FLT_2ms,
.iomap = TCFG_IOKEY_MOUSE_HK_PORT, //唤醒口选择
};
const struct wakeup_param wk_param = {
#if TCFG_CODE_SWITCH_ENABLE
.port[1] = &port0,
.port[2] = &port1,
#endif /* TCFG_CODE_SWITCH_ENABLE*/
#if TCFG_OMSENSOR_ENABLE
.port[3] = &port2,
#endif /* TCFG_OMSENSOR_ENABLE*/
#if TCFG_IOKEY_ENABLE
.port[4] = &port3,
.port[5] = &port4,
.port[6] = &port5,
#endif /* TCFG_IOKEY_ENABLE */
};
void mouse_board_devices_init(void)
{
#if TCFG_CODE_SWITCH_ENABLE
code_switch_init(&sw_data);
#endif /* TCFG_CODE_SWITCH_ENABLE*/
#if TCFG_OMSENSOR_ENABLE
optical_mouse_sensor_init(&OMSensor_data);
#endif /* TCFG_OMSENSOR_ENABLE*/
#if TCFG_IOKEY_ENABLE
key_driver_init();
#endif /* TCFG_IOKEY_ENABLE */
}
void debug_uart_init(const struct uart_platform_data *data)
{
#if TCFG_UART0_ENABLE
if (data) {
uart_init(data);
} else {
uart_init(&uart0_data);
}
#endif
}
void gSensor_wkupup_disable(void)
{
log_info("gSensor wkup disable\n");
power_wakeup_index_disable(3);
}
void gSensor_wkupup_enable(void)
{
log_info("gSensor wkup enable\n");
power_wakeup_index_enable(3);
}
static void board_devices_init(void)
{
#if (TCFG_IOKEY_ENABLE || TCFG_ADKEY_ENABLE)
key_driver_init();
#endif
#if TCFG_UART_KEY_ENABLE
extern int uart_key_init(void);
uart_key_init();
#endif /* #if TCFG_UART_KEY_ENABLE */
}
extern void cfg_file_parse(u8 idx);
void board_init()
{
board_power_init();
adc_vbg_init();
adc_init();
cfg_file_parse(0);
devices_init();
board_devices_init();
if(get_charge_online_flag()){
power_set_mode(PWR_LDO15);
}else{
power_set_mode(TCFG_LOWPOWER_POWER_SEL);
}
#if TCFG_UART0_ENABLE
if (uart0_data.rx_pin < IO_MAX_NUM) {
gpio_set_die(uart0_data.rx_pin, 1);
}
#endif
//
#if(!TCFG_CHARGE_ENABLE)
CHARGE_EN(0);
CHGBG_EN(0);
}
#endif
//maskrom 使用到的io
static void mask_io_cfg()
{
struct boot_soft_flag_t boot_soft_flag = {0};
boot_soft_flag.flag0.boot_ctrl.wdt_dis = 0;
boot_soft_flag.flag0.boot_ctrl.poweroff = 0;
boot_soft_flag.flag0.boot_ctrl.is_port_b = JL_IOMAP->CON0 & BIT(16) ? 1 : 0;
boot_soft_flag.flag1.misc.usbdm = SOFTFLAG_HIGH_RESISTANCE;
boot_soft_flag.flag1.misc.usbdp = SOFTFLAG_HIGH_RESISTANCE;
boot_soft_flag.flag1.misc.uart_key_port = 0;
boot_soft_flag.flag1.misc.ldoin = SOFTFLAG_HIGH_RESISTANCE;
boot_soft_flag.flag2.pa7_pb4.pa7 = SOFTFLAG_HIGH_RESISTANCE;
boot_soft_flag.flag2.pa7_pb4.pb4 = SOFTFLAG_HIGH_RESISTANCE;
boot_soft_flag.flag3.pc3_pc5.pc3 = SOFTFLAG_OUT1; //touch key power support
boot_soft_flag.flag3.pc3_pc5.pc5 = SOFTFLAG_HIGH_RESISTANCE;
mask_softflag_config(&boot_soft_flag);
}
//-----------------------------------------------
static struct port_wakeup add_port = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.both_edge = 0,
.filter = PORT_FLT_NULL,
.iomap = 0, //唤醒口选择
};
const struct wakeup_param wk_param_add_io = {
#if TCFG_CODE_SWITCH_ENABLE
.port[1] = &port0,
.port[2] = &port1,
#endif /* TCFG_CODE_SWITCH_ENABLE*/
#if TCFG_OMSENSOR_ENABLE
.port[3] = &port2,
#endif /* TCFG_OMSENSOR_ENABLE*/
#if TCFG_IOKEY_ENABLE
.port[4] = &port3,
.port[5] = &port4,
.port[6] = &port5,
#endif /* TCFG_IOKEY_ENABLE */
.port[7] = &add_port,
};
enum {
PORTA_GROUP = 0,
PORTB_GROUP,
PORTC_GROUP,
PORTD_GROUP,
};
static void port_protect(u16 *port_group, u32 port_num)
{
if (port_num == NO_CONFIG_PORT) {
return;
}
port_group[port_num / IO_GROUP_NUM] &= ~BIT(port_num % IO_GROUP_NUM);
}
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
static void close_gpio(void)
{
u16 port_group[] = {
[PORTA_GROUP] = 0x1ff,
[PORTB_GROUP] = 0x3ff,
[PORTC_GROUP] = 0x3ff,
[PORTD_GROUP] = 0x3ff,
};
#if TCFG_CODE_SWITCH_ENABLE
port_protect(port_group, TCFG_CODE_SWITCH_A_PHASE_PORT);
port_protect(port_group, TCFG_CODE_SWITCH_B_PHASE_PORT);
#endif /* TCFG_CODE_SWITCH_ENABLE */
#if TCFG_OMSENSOR_ENABLE
port_protect(port_group, TCFG_OPTICAL_SENSOR_SCLK_PORT);
port_protect(port_group, TCFG_OPTICAL_SENSOR_DATA_PORT);
port_protect(port_group, TCFG_OPTICAL_SENSOR_INT_PORT);
#endif /* TCFG_OMSENSOR_ENABLE */
#if TCFG_IOKEY_ENABLE
port_protect(port_group, TCFG_IOKEY_MOUSE_LK_PORT);
port_protect(port_group, TCFG_IOKEY_MOUSE_RK_PORT);
port_protect(port_group, TCFG_IOKEY_MOUSE_HK_PORT);
#endif /* TCFG_IOKEY_ENABLE */
#if TCFG_RTC_ALARM_ENABLE
port_protect(port_group, IO_PORTA_01);
port_protect(port_group, IO_PORTA_02);
#endif /* TCFG_RTC_ALARM_ENABLE */
//< close gpio
gpio_dir(GPIOA, 0, 9, port_group[PORTA_GROUP], GPIO_OR);
gpio_set_pu(GPIOA, 0, 9, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_set_pd(GPIOA, 0, 9, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_die(GPIOA, 0, 9, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_dieh(GPIOA, 0, 9, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_dir(GPIOB, 0, 10, port_group[PORTB_GROUP], GPIO_OR);
gpio_set_pu(GPIOB, 0, 10, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_set_pd(GPIOB, 0, 10, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_die(GPIOB, 0, 10, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_dieh(GPIOB, 0, 10, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_dir(GPIOC, 0, 10, port_group[PORTC_GROUP], GPIO_OR);
gpio_set_pu(GPIOC, 0, 10, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_set_pd(GPIOC, 0, 10, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_die(GPIOC, 0, 10, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_dieh(GPIOC, 0, 10, ~port_group[PORTC_GROUP], GPIO_AND);
//< close usb io
usb_iomode(1);
}
void power_wakeup_add_io(int io)
{
log_info("reset wakeup add io");
add_port.iomap = io;
power_wakeup_init(&wk_param_add_io);
}
//-----------------------------------------------
static void keep_set_io_output(int io_sel,int en)
{
gpio_set_pull_up(io_sel, 0);
gpio_set_pull_down(io_sel, 0);
gpio_set_direction(io_sel, 0);
gpio_set_die(io_sel, 1);
gpio_set_output_value(io_sel, en);
}
static void keep_set_io_input(int io_sel,u8 pull_up_en,u8 pull_down_en)
{
gpio_set_pull_up(io_sel, pull_up_en);
gpio_set_pull_down(io_sel, pull_down_en);
gpio_set_direction(io_sel, 1);
gpio_set_die(io_sel, 0);
}
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
extern void dac_power_off(void);
void board_set_soft_poweroff(void)
{
u32 porta_value = 0xffff & (~BIT(3));
u32 portb_value = 0xffff & ~(BIT(1)|BIT(6)|BIT(7));
u32 portc_value = 0xffff & ~(BIT(4)|BIT(5));
printf("portb_value %x\n",portb_value);
/* gpio_direction_output(IO_PORTC_03, 1); //touch chip power support */
mask_io_cfg();
gpio_set_pu(GPIOA, 0, 16, ~porta_value, GPIO_AND);
gpio_set_pd(GPIOA, 0, 16, ~porta_value, GPIO_AND);
gpio_die(GPIOA, 0, 16, ~porta_value, GPIO_AND);
gpio_dieh(GPIOA, 0, 16, ~porta_value, GPIO_AND);
gpio_dir(GPIOA, 0, 16, porta_value, GPIO_OR);
gpio_set_pu(GPIOB, 0, 16, ~portb_value, GPIO_AND);
gpio_set_pd(GPIOB, 0, 16, ~portb_value, GPIO_AND);
gpio_die(GPIOB, 0, 16, ~portb_value, GPIO_AND);
gpio_dieh(GPIOB, 0, 16, ~portb_value, GPIO_AND);
gpio_dir(GPIOB, 0, 16, portb_value, GPIO_OR);
gpio_set_pu(GPIOC, 0, 16, ~portc_value, GPIO_AND);
gpio_set_pd(GPIOC, 0, 16, ~portc_value, GPIO_AND);
gpio_die(GPIOC, 0, 16, ~portc_value, GPIO_AND);
gpio_dieh(GPIOC, 0, 16, ~portc_value, GPIO_AND);
gpio_dir(GPIOC, 0, 16, portc_value, GPIO_OR);
/*
gpio_set_pu(GPIOD, 0, 16, ~portd_value, GPIO_AND);
gpio_set_pd(GPIOD, 0, 16, ~portd_value, GPIO_AND);
gpio_die(GPIOD, 0, 16, ~portd_value, GPIO_AND);
gpio_dieh(GPIOD, 0, 16, ~portd_value, GPIO_AND);
gpio_dir(GPIOD, 0, 16, portd_value, GPIO_OR);
*/
gpio_set_pull_up(IO_PORTP_00, 0);
gpio_set_pull_down(IO_PORTP_00, 0);
gpio_set_die(IO_PORTP_00, 0);
gpio_set_dieh(IO_PORTP_00, 0);
gpio_set_direction(IO_PORTP_00, 1);
gpio_set_pull_up(IO_PORT_DP, 0);
gpio_set_pull_down(IO_PORT_DP, 0);
gpio_set_die(IO_PORT_DP, 0);
gpio_set_dieh(IO_PORT_DP, 0);
gpio_set_direction(IO_PORT_DP, 1);
gpio_set_pull_up(IO_PORT_DM, 0);
gpio_set_pull_down(IO_PORT_DM, 0);
gpio_set_die(IO_PORT_DM, 0);
gpio_set_dieh(IO_PORT_DM, 0);
gpio_set_direction(IO_PORT_DM, 1);
if(add_port.iomap){
keep_set_io_input(add_port.iomap,add_port.pullup_down_enable,add_port.pullup_down_enable);
}
/* dac_power_off(); */
}
#define APP_IO_DEBUG_0(i,x) //{JL_PORT##i->DIR &= ~BIT(x), JL_PORT##i->OUT &= ~BIT(x);}
#define APP_IO_DEBUG_1(i,x) //{JL_PORT##i->DIR &= ~BIT(x), JL_PORT##i->OUT |= BIT(x);}
void sleep_exit_callback(u32 usec)
{
putchar('>');
APP_IO_DEBUG_1(B, 0);
}
void sleep_enter_callback(u8 step)
{
/* 此函数禁止添加打印 */
if (step == 1) {
putchar('<');
APP_IO_DEBUG_0(B, 0);
#if 0//??? TCFG_CODE_SWITCH_ENABLE
if (gpio_read(sw_data.a_phase_io) == 0) {
wk_param.port[1]->edge = RISING_EDGE;
} else if (gpio_read(sw_data.a_phase_io) == 1) {
wk_param.port[1]->edge = FALLING_EDGE;
}
power_wakeup_port_set(1, wk_param.port[1]);
if (gpio_read(sw_data.b_phase_io) == 0) {
wk_param.port[2]->edge = RISING_EDGE;
} else if (gpio_read(sw_data.b_phase_io) == 1) {
wk_param.port[2]->edge = FALLING_EDGE;
}
power_wakeup_port_set(2, wk_param.port[2]);
#endif
/* dac_power_off(); */
} else {
/*
gpio_set_pull_up(IO_PORTA_03, 0);
gpio_set_pull_down(IO_PORTA_03, 0);
gpio_set_direction(IO_PORTA_03, 1);
usb_iomode(1);
gpio_set_pull_up(IO_PORT_DP, 0);
gpio_set_pull_down(IO_PORT_DP, 0);
gpio_set_direction(IO_PORT_DP, 1);
gpio_set_die(IO_PORT_DP, 0);
gpio_set_pull_up(IO_PORT_DM, 0);
gpio_set_pull_down(IO_PORT_DM, 0);
gpio_set_direction(IO_PORT_DM, 1);
gpio_set_die(IO_PORT_DM, 0);
*/
close_gpio();
}
}
static void wl_audio_clk_on(void)
{
JL_WL_AUD->CON0 = 1;
}
//-----------------------------------------------
static void wakeup_callback(u8 index, u8 gpio)
{
//printf("index is 0x%x, gpio is 0x%x\n", index, gpio);
}
void board_power_init(void)
{
log_info("Power init : %s", __FILE__);
/* gpio_direction_output(IO_PORTC_03, 1); //touch chip power support */
power_init(&power_param);
power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff);
wl_audio_clk_on();
power_keep_dacvdd_en(0);
port_edge_wkup_set_callback(wakeup_callback);
power_wakeup_init(&wk_param);
//wdt_close();
//while(1);
#if (!TCFG_IOKEY_ENABLE && !TCFG_ADKEY_ENABLE)
charge_check_and_set_pinr(1);
#endif
}
#endif /* #ifdef CONFIG_BOARD_AC697X_DEMO */
Reference in New Issue Copy Permalink