huangjin/AC63_BT_SDK
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
AC63_BT_SDK/apps/mesh/board/br25/board_ac636n_demo.c

483 lines
15 KiB
C
Raw Normal View History

原始文件
2025-02-18 15:40:42 +08:00
#include "app_config.h"
#ifdef CONFIG_BOARD_AC636N_DEMO
#include "system/includes.h"
#include "asm/charge.h"
#include "device/key_driver.h"
#include "asm/power/p33.h"
#include "asm/pwm_led.h"
#ifdef CONFIG_LITE_AUDIO
#include "media/includes.h"
#endif/*CONFIG_LITE_AUDIO*/
#include "asm/power/power_port.h"
#define LOG_TAG_CONST BOARD
#define LOG_TAG "[BOARD]"
#define LOG_ERROR_ENABLE
#define LOG_DEBUG_ENABLE
#define LOG_INFO_ENABLE
/* #define LOG_DUMP_ENABLE */
#define LOG_CLI_ENABLE
#include "debug.h"
void board_power_init(void);
/************************** LOW POWER config ****************************/
const struct low_power_param power_param = {
.config = TCFG_LOWPOWER_LOWPOWER_SEL, //0：sniff时芯片不进入低功耗 1：sniff时芯片进入powerdown
.btosc_hz = TCFG_CLOCK_OSC_HZ, //外接晶振频率
.delay_us = TCFG_CLOCK_SYS_HZ / 1000000L, //提供给低功耗模块的延时(不需要需修改)
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.6V
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
.osc_type = OSC_TYPE_LRC,
.dcdc_port = TCFG_DCDC_PORT_SEL,
};
/************************** KEY MSG****************************/
/*各个按键的消息设置，如果USER_CFG中设置了USE_CONFIG_KEY_SETTING为1，则会从配置文件读取对应的配置来填充改结构体*/
u8 key_table[KEY_NUM_MAX][KEY_EVENT_MAX] = {
// SHORT LONG HOLD UP DOUBLE TRIPLE
};
// *INDENT-OFF*
/************************** UART config****************************/
#if TCFG_UART0_ENABLE
UART0_PLATFORM_DATA_BEGIN(uart0_data)
.tx_pin = TCFG_UART0_TX_PORT, //串口打印TX引脚选择
.rx_pin = TCFG_UART0_RX_PORT, //串口打印RX引脚选择
.baudrate = TCFG_UART0_BAUDRATE, //串口波特率
.flags = UART_DEBUG, //串口用来打印需要把改参数设置为UART_DEBUG
UART0_PLATFORM_DATA_END()
#endif //TCFG_UART0_ENABLE
/************************** AD KEY ****************************/
#if TCFG_ADKEY_ENABLE
const struct adkey_platform_data adkey_data = {
.enable = TCFG_ADKEY_ENABLE, //AD按键使能
.adkey_pin = TCFG_ADKEY_PORT, //AD按键对应引脚
.ad_channel = TCFG_ADKEY_AD_CHANNEL, //AD通道值
.extern_up_en = TCFG_ADKEY_EXTERN_UP_ENABLE, //是否使用外接上拉电阻
.ad_value = { //根据电阻算出来的电压值
TCFG_ADKEY_VOLTAGE0,
TCFG_ADKEY_VOLTAGE1,
TCFG_ADKEY_VOLTAGE2,
TCFG_ADKEY_VOLTAGE3,
TCFG_ADKEY_VOLTAGE4,
TCFG_ADKEY_VOLTAGE5,
TCFG_ADKEY_VOLTAGE6,
TCFG_ADKEY_VOLTAGE7,
TCFG_ADKEY_VOLTAGE8,
TCFG_ADKEY_VOLTAGE9,
},
.key_value = { //AD按键各个按键的键值
TCFG_ADKEY_VALUE0,
TCFG_ADKEY_VALUE1,
TCFG_ADKEY_VALUE2,
TCFG_ADKEY_VALUE3,
TCFG_ADKEY_VALUE4,
TCFG_ADKEY_VALUE5,
TCFG_ADKEY_VALUE6,
TCFG_ADKEY_VALUE7,
TCFG_ADKEY_VALUE8,
TCFG_ADKEY_VALUE9,
},
};
#endif
#if TCFG_IRKEY_ENABLE
const struct irkey_platform_data irkey_data = {
.enable = TCFG_IRKEY_ENABLE, //IR按键使能
.port = TCFG_IRKEY_PORT, //IR按键口
};
#endif
/************************** IO KEY ****************************/
#if TCFG_IOKEY_ENABLE
const struct iokey_port iokey_list[] = {
{
.connect_way = TCFG_IOKEY_POWER_CONNECT_WAY, //IO按键的连接方式
.key_type.one_io.port = TCFG_IOKEY_POWER_ONE_PORT, //IO按键对应的引脚
.key_value = 0, //按键值
},
#if(!TCFG_UART0_ENABLE || TCFG_UART0_TX_PORT != IO_PORT_DP)
{
.connect_way = TCFG_IOKEY_PREV_CONNECT_WAY,
.key_type.one_io.port = TCFG_IOKEY_PREV_ONE_PORT,
.key_value = 1,
},
#endif
{
.connect_way = TCFG_IOKEY_NEXT_CONNECT_WAY,
.key_type.one_io.port = TCFG_IOKEY_NEXT_ONE_PORT,
.key_value = 2,
},
};
const struct iokey_platform_data iokey_data = {
.enable = TCFG_IOKEY_ENABLE, //是否使能IO按键
.num = ARRAY_SIZE(iokey_list), //IO按键的个数
.port = iokey_list, //IO按键参数表
};
#if MULT_KEY_ENABLE
//组合按键消息映射表
//配置注意事项:单个按键按键值需要按照顺序编号,如power:0, prev:1, next:2
//bit_value = BIT(0) | BIT(1) 指按键值为0和按键值为1的两个按键被同时按下,
//remap_value = 3指当这两个按键被同时按下后重新映射的按键值;
const struct key_remap iokey_remap_table[] = {
{.bit_value = BIT(0) | BIT(1), .remap_value = 3},
{.bit_value = BIT(0) | BIT(2), .remap_value = 4},
{.bit_value = BIT(1) | BIT(2), .remap_value = 5},
};
const struct key_remap_data iokey_remap_data = {
.remap_num = ARRAY_SIZE(iokey_remap_table),
.table = iokey_remap_table,
};
#endif
#endif
void debug_uart_init(const struct uart_platform_data *data)
{
#if TCFG_UART0_ENABLE
if (data) {
uart_init(data);
} else {
uart_init(&uart0_data);
}
#endif
}
/************************** PWM_LED ****************************/
#if TCFG_PWMLED_ENABLE
LED_PLATFORM_DATA_BEGIN(pwm_led_data)
.io_mode = TCFG_PWMLED_IOMODE, //推灯模式设置:支持单个IO推两个灯和两个IO推两个灯
.io_cfg.one_io.pin = TCFG_PWMLED_PIN, //单个IO推两个灯的IO口配置
LED_PLATFORM_DATA_END()
#endif
static void board_devices_init(void)
{
#if TCFG_PWMLED_ENABLE
pwm_led_init(&pwm_led_data);
#endif
#if (TCFG_IOKEY_ENABLE || TCFG_ADKEY_ENABLE || TCFG_IRKEY_ENABLE || TCFG_TOUCH_KEY_ENABLE)
key_driver_init();
#endif
}
extern void cfg_file_parse(u8 idx);
void board_init()
{
board_power_init();
adc_vbg_init();
adc_init();
cfg_file_parse(0);
devices_init();
board_devices_init();
log_info("board_init");
//必须在切换到dcdc前设置好
if(get_charge_online_flag()){
log_info("charge...select LDO15");
power_set_mode(PWR_LDO15);
}else{
power_set_mode(TCFG_LOWPOWER_POWER_SEL);
}
#if(!TCFG_CHARGE_ENABLE)
/*close FAST CHARGE */
CHARGE_EN(0);
CHGBG_EN(0);
#endif
}
/************************** DAC ****************************/
#if TCFG_AUDIO_DAC_ENABLE
struct dac_platform_data dac_data = {
.ldo_volt = TCFG_AUDIO_DAC_LDO_VOLT, //DACVDD等级.需要根据具体硬件来设置（高低压）可选:1.2V/1.3V/2.35V/2.5V/2.65V/2.8V/2.95V/3.1V
#if ((TCFG_AUDIO_DAC_CONNECT_MODE == DAC_OUTPUT_FRONT_LR_REAR_LR) || (TCFG_AUDIO_DAC_CONNECT_MODE == DAC_OUTPUT_DUAL_LR_DIFF))
.vcmo_en = 0, //四声道与双声道差分关闭VCOMO
#else
.vcmo_en = 0, //是否打开VCOMO
#endif
.output = TCFG_AUDIO_DAC_CONNECT_MODE, //DAC输出配置，和具体硬件连接有关，需根据硬件来设置
.ldo_isel = 3,
.ldo_fb_isel = 2,
.lpf_isel = 0x8,
};
#endif
/************************** ADC ****************************/
#if TCFG_AUDIO_ADC_ENABLE
const struct ladc_port ladc_list[] = {
{// 0
.channel = TCFG_AUDIO_ADC_LINE_CHA0,
},
{// 1
.channel = TCFG_AUDIO_ADC_LINE_CHA1,
},
// total must < 4
};
struct adc_platform_data adc_data = {
.mic_channel = TCFG_AUDIO_ADC_MIC_CHA, //MIC通道选择，对于693x，MIC只有一个通道，固定选择右声道
/*MIC LDO电流档位设置：
0:0.625ua 1:1.25ua 2:1.875ua 3:2.5ua*/
.mic_ldo_isel = TCFG_AUDIO_ADC_LDO_SEL,
/*MIC 是否省隔直电容：
0: 不省电容 1: 省电容 */
#if ((TCFG_AUDIO_DAC_CONNECT_MODE == DAC_OUTPUT_FRONT_LR_REAR_LR) || (TCFG_AUDIO_DAC_CONNECT_MODE == DAC_OUTPUT_DUAL_LR_DIFF))
.mic_capless = 0,//四声道与双声道差分使用，不省电容接法
#else
.mic_capless = 0,
#endif
/*MIC免电容方案需要设置，影响MIC的偏置电压
21:1.18K 20:1.42K 19:1.55K 18:1.99K 17:2.2K 16:2.4K 15:2.6K 14:2.91K 13:3.05K 12:3.5K 11:3.73K
10:3.91K 9:4.41K 8:5.0K 7:5.6K 6:6K 5:6.5K 4:7K 3:7.6K 2:8.0K 1:8.5K */
.mic_bias_res = 16,
/*MIC LDO电压档位设置,也会影响MIC的偏置电压
0:2.3v 1:2.5v 2:2.7v 3:3.0v */
.mic_ldo_vsel = 2,
/*MIC电容隔直模式使用内部mic偏置(PC7)*/
.mic_bias_inside = 1,
/*保持内部mic偏置输出*/
.mic_bias_keep = 0,
// ladc 通道
.ladc_num = ARRAY_SIZE(ladc_list),
.ladc = ladc_list,
};
#endif
/************************** PWR config ****************************/
struct port_wakeup port0 = {
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
.attribute = BLUETOOTH_RESUME, //保留参数
#if TCFG_ADKEY_ENABLE
.iomap = TCFG_ADKEY_PORT, //唤醒口选择
#endif
#if TCFG_IOKEY_ENABLE
.iomap = TCFG_IOKEY_POWER_ONE_PORT, //唤醒口选择
#endif
.filter_enable = ENABLE,
};
const struct sub_wakeup sub_wkup = {
.attribute = BLUETOOTH_RESUME,
};
const struct charge_wakeup charge_wkup = {
.attribute = BLUETOOTH_RESUME,
};
const struct wakeup_param wk_param = {
.filter = PORT_FLT_2ms,
#if TCFG_ADKEY_ENABLE || TCFG_IOKEY_ENABLE
.port[1] = &port0,
#endif
.sub = &sub_wkup,
.charge = &charge_wkup,
};
//-----------------------------------------------
static void keep_set_io_output(int io_sel,int en)
{
gpio_set_pull_up(io_sel, 0);
gpio_set_pull_down(io_sel, 0);
gpio_set_direction(io_sel, 0);
gpio_set_die(io_sel, 1);
gpio_set_output_value(io_sel, en);
}
static void keep_set_io_input(int io_sel,u8 pull_up_en,u8 pull_down_en)
{
gpio_set_pull_up(io_sel, pull_up_en);
gpio_set_pull_down(io_sel, pull_down_en);
gpio_set_direction(io_sel, 1);
gpio_set_die(io_sel, 0);
}
/*note:
1.sleep流程禁止耗时操作。
2.上电初始化将所有io配置为高阻，低功耗流程请将io配置为高阻/确定状态。
*/
extern void dac_power_off(void);
u32 spi_get_port(void);
void board_set_soft_poweroff(void)
{
u16 port_group[] = {
[PORTA_GROUP] = 0xffff,
[PORTB_GROUP] = 0xffff,
[PORTC_GROUP] = 0xffff,
[PORTD_GROUP] = 0Xffff,
};
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15){
power_set_mode(PWR_LDO15);
}
/* port_protect(port_group, IO_PORTC_04); */
//flash电源
if(spi_get_port()==0){
port_protect(port_group, SPI0_PWR_A);
port_protect(port_group, SPI0_CS_A);
port_protect(port_group, SPI0_CLK_A);
port_protect(port_group, SPI0_DO_D0_A);
port_protect(port_group, SPI0_DI_D1_A);
if(get_sfc_bit_mode()==4){
port_protect(port_group, SPI0_WP_D2_A);
port_protect(port_group, SPI0_HOLD_D3_A);
}
}else{
port_protect(port_group, SPI0_PWR_B);
port_protect(port_group, SPI0_CS_B);
port_protect(port_group, SPI0_CLK_B);
port_protect(port_group, SPI0_DO_D0_B);
port_protect(port_group, SPI0_DI_D1_B);
if(get_sfc_bit_mode()==4){
port_protect(port_group, SPI0_WP_D2_B);
port_protect(port_group, SPI0_HOLD_D3_B);
}
}
#if TCFG_ADKEY_ENABLE
port_protect(port_group,TCFG_ADKEY_PORT);
#endif
#if TCFG_IOKEY_ENABLE
port_protect(port_group, TCFG_IOKEY_POWER_ONE_PORT);
port_protect(port_group, TCFG_IOKEY_PREV_ONE_PORT);
port_protect(port_group, TCFG_IOKEY_NEXT_ONE_PORT);
#endif /* TCFG_IOKEY_ENABLE */
//< close gpio
gpio_dir(GPIOA, 0, 16, port_group[PORTA_GROUP], GPIO_OR);
gpio_set_pu(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_set_pd(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_die(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_dieh(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
gpio_dir(GPIOB, 0, 16, port_group[PORTB_GROUP], GPIO_OR);
gpio_set_pu(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_set_pd(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_die(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_dieh(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
gpio_dir(GPIOC, 0, 16, port_group[PORTC_GROUP], GPIO_OR);
gpio_set_pu(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_set_pd(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_die(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_dieh(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
gpio_dir(GPIOD, 0, 16, port_group[PORTD_GROUP], GPIO_OR);
gpio_set_pu(GPIOD, 0, 16, ~port_group[PORTD_GROUP], GPIO_AND);
gpio_set_pd(GPIOD, 0, 16, ~port_group[PORTD_GROUP], GPIO_AND);
gpio_die(GPIOD, 0, 16, ~port_group[PORTD_GROUP], GPIO_AND);
gpio_dieh(GPIOD, 0, 16, ~port_group[PORTD_GROUP], GPIO_AND);
usb_iomode(1);
gpio_set_pull_up(IO_PORT_DP, 0);
gpio_set_pull_down(IO_PORT_DP, 0);
gpio_set_direction(IO_PORT_DP, 1);
gpio_set_die(IO_PORT_DP, 0);
gpio_set_dieh(IO_PORT_DP, 0);
gpio_set_pull_up(IO_PORT_DM, 0);
gpio_set_pull_down(IO_PORT_DM, 0);
gpio_set_direction(IO_PORT_DM, 1);
gpio_set_die(IO_PORT_DM, 0);
gpio_set_dieh(IO_PORT_DM, 0);
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15
&& TCFG_DCDC_PORT_SEL != NO_CONFIG_PORT){
//need keep dcdc's io output 0
keep_set_io_output(TCFG_DCDC_PORT_SEL,0);
}
}
void sleep_exit_callback(u32 usec)
{
putchar('>');
}
void sleep_enter_callback(u8 step)
{
/* 此函数禁止添加打印 */
if (step == 1) {
putchar('<');
#if TCFG_AUDIO_ENABLE
dac_power_off();
#endif/*TCFG_AUDIO_ENABLE*/
} else {
usb_iomode(1);
gpio_set_pull_up(IO_PORT_DP, 0);
gpio_set_pull_down(IO_PORT_DP, 0);
gpio_set_direction(IO_PORT_DP, 1);
gpio_set_die(IO_PORT_DP, 0);
gpio_set_dieh(IO_PORT_DP, 0);
gpio_set_pull_up(IO_PORT_DM, 0);
gpio_set_pull_down(IO_PORT_DM, 0);
gpio_set_direction(IO_PORT_DM, 1);
gpio_set_die(IO_PORT_DM, 0);
gpio_set_dieh(IO_PORT_DM, 0);
}
}
void board_power_init(void)
{
log_info("Power init : %s", __FILE__);
//< close short key reset
/* p33_and_1byte(P3_PR_PWR, ~BIT(3)); */
//< close long key reset
/* p33_and_1byte(P3_PINR_CON, 0); */
gpio_longpress_pin0_reset_config(IO_PORTB_01, 0, 0);
gpio_shortpress_reset_config(0);//1--enable 0--disable
power_init(&power_param);
//< close long key reset
VCM_DET_EN(0);
power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff);
power_keep_dacvdd_en(0);
power_wakeup_init(&wk_param);
/* #if (!TCFG_IOKEY_ENABLE && !TCFG_ADKEY_ENABLE) */
/* charge_check_and_set_pinr(0); */
/* #endif */
}
#endif
Reference in New Issue Copy Permalink