#ifndef _CHARGE_H_ #define _CHARGE_H_ #include "typedef.h" #include "device.h" /*------充满电电压选择 3.962V-4.611V-------*/ #define CHARGE_FULL_V_3962 0 #define CHARGE_FULL_V_4002 1 #define CHARGE_FULL_V_4044 2 #define CHARGE_FULL_V_4086 3 #define CHARGE_FULL_V_4130 4 #define CHARGE_FULL_V_4175 5 #define CHARGE_FULL_V_4222 6 #define CHARGE_FULL_V_4270 7 #define CHARGE_FULL_V_4308 8 #define CHARGE_FULL_V_4349 9 #define CHARGE_FULL_V_4391 10 #define CHARGE_FULL_V_4434 11 #define CHARGE_FULL_V_4472 12 #define CHARGE_FULL_V_4517 13 #define CHARGE_FULL_V_4564 14 #define CHARGE_FULL_V_4611 15 #define CHARGE_FULL_V_MAX 16 /*****************************************/ /*充满电电流选择 2mA-30mA*/ #define CHARGE_FULL_mA_2 0 #define CHARGE_FULL_mA_5 1 #define CHARGE_FULL_mA_7 2 #define CHARGE_FULL_mA_10 3 #define CHARGE_FULL_mA_15 4 #define CHARGE_FULL_mA_20 5 #define CHARGE_FULL_mA_25 6 #define CHARGE_FULL_mA_30 7 /* 充电电流选择 恒流：20-220mA */ #define CHARGE_mA_20 0 #define CHARGE_mA_30 1 #define CHARGE_mA_40 2 #define CHARGE_mA_50 3 #define CHARGE_mA_60 4 #define CHARGE_mA_70 5 #define CHARGE_mA_80 6 #define CHARGE_mA_90 7 #define CHARGE_mA_100 8 #define CHARGE_mA_110 9 #define CHARGE_mA_120 10 #define CHARGE_mA_140 11 #define CHARGE_mA_160 12 #define CHARGE_mA_180 13 #define CHARGE_mA_200 14 #define CHARGE_mA_220 15 /* 充电口下拉选择 电阻 50k ~ 200k */ #define CHARGE_PULLDOWN_50K 0 #define CHARGE_PULLDOWN_100K 1 #define CHARGE_PULLDOWN_150K 2 #define CHARGE_PULLDOWN_200K 3 #define CHARGE_CCVOL_V 300 //最低充电电流档转向用户设置充电电流档的电压转换点(AC693X无涓流充电，电池电压低时采用最低电流档，电池电压大于设置的值时采用用户设置的充电电流档) #define DEVICE_EVENT_FROM_CHARGE (('C' << 24) | ('H' << 16) | ('G' << 8) | '\0') struct charge_platform_data { u8 charge_en; //内置充电使能 u8 charge_poweron_en; //开机充电使能 u8 charge_full_V; //充满电电压大小 u8 charge_full_mA; //充满电电流大小 u8 charge_mA; //充电电流大小 u8 ldo5v_pulldown_en; //下拉使能位 u8 ldo5v_pulldown_lvl; //ldo5v的下拉电阻配置项,若充电舱需要更大的负载才能检测到插入时，请将该变量置为对应阻值 u8 ldo5v_pulldown_keep; //下拉电阻在softoff时是否保持,ldo5v_pulldown_en=1时有效 u16 ldo5v_off_filter; //ldo5v拔出过滤值，过滤时间 = (filter*2 + 20)ms,ldoin<0.6V且时间大于过滤时间才认为拔出,对于充满直接从5V掉到0V的充电仓，该值必须设置成0，对于充满由5V先掉到0V之后再升压到xV的充电仓，需要根据实际情况设置该值大小 u16 ldo5v_on_filter; //ldo5v>vbat插入过滤值,电压的过滤时间 = (filter*2)ms u16 ldo5v_keep_filter; //1V