133 lines
4.2 KiB
C
133 lines
4.2 KiB
C
#ifndef _CHARGE_H_
|
||
#define _CHARGE_H_
|
||
|
||
#include "typedef.h"
|
||
|
||
/*------充满电电压选择 3.962V-4.611V-------*/
|
||
#define CHARGE_FULL_V_3962 0
|
||
#define CHARGE_FULL_V_4002 1
|
||
#define CHARGE_FULL_V_4044 2
|
||
#define CHARGE_FULL_V_4086 3
|
||
#define CHARGE_FULL_V_4130 4
|
||
#define CHARGE_FULL_V_4175 5
|
||
#define CHARGE_FULL_V_4222 6
|
||
#define CHARGE_FULL_V_4270 7
|
||
#define CHARGE_FULL_V_4308 8
|
||
#define CHARGE_FULL_V_4349 9
|
||
#define CHARGE_FULL_V_4391 10
|
||
#define CHARGE_FULL_V_4434 11
|
||
#define CHARGE_FULL_V_4472 12
|
||
#define CHARGE_FULL_V_4517 13
|
||
#define CHARGE_FULL_V_4564 14
|
||
#define CHARGE_FULL_V_4611 15
|
||
#define CHARGE_FULL_V_MAX 16
|
||
/*****************************************/
|
||
|
||
/*充满电电流选择 2mA-30mA*/
|
||
#define CHARGE_FULL_mA_2 0
|
||
#define CHARGE_FULL_mA_5 1
|
||
#define CHARGE_FULL_mA_7 2
|
||
#define CHARGE_FULL_mA_10 3
|
||
#define CHARGE_FULL_mA_15 4
|
||
#define CHARGE_FULL_mA_20 5
|
||
#define CHARGE_FULL_mA_25 6
|
||
#define CHARGE_FULL_mA_30 7
|
||
|
||
/*
|
||
充电电流选择
|
||
恒流：20-220mA
|
||
*/
|
||
#define CHARGE_mA_20 0
|
||
#define CHARGE_mA_30 1
|
||
#define CHARGE_mA_40 2
|
||
#define CHARGE_mA_50 3
|
||
#define CHARGE_mA_60 4
|
||
#define CHARGE_mA_70 5
|
||
#define CHARGE_mA_80 6
|
||
#define CHARGE_mA_90 7
|
||
#define CHARGE_mA_100 8
|
||
#define CHARGE_mA_110 9
|
||
#define CHARGE_mA_120 10
|
||
#define CHARGE_mA_140 11
|
||
#define CHARGE_mA_160 12
|
||
#define CHARGE_mA_180 13
|
||
#define CHARGE_mA_200 14
|
||
#define CHARGE_mA_220 15
|
||
|
||
/*
|
||
充电口下拉选择
|
||
电阻 50k ~ 200k
|
||
*/
|
||
#define CHARGE_PULLDOWN_50K 0
|
||
#define CHARGE_PULLDOWN_100K 1
|
||
#define CHARGE_PULLDOWN_150K 2
|
||
#define CHARGE_PULLDOWN_200K 3
|
||
|
||
|
||
#define CHARGE_CCVOL_V 300 //最低充电电流档转向用户设置充电电流档的电压转换点(AC693X无涓流充电，电池电压低时采用最低电流档，电池电压大于设置的值时采用用户设置的充电电流档)
|
||
|
||
#define DEVICE_EVENT_FROM_CHARGE (('C' << 24) | ('H' << 16) | ('G' << 8) | '\0')
|
||
|
||
|
||
struct charge_platform_data {
|
||
u8 charge_en; //内置充电使能
|
||
u8 charge_poweron_en; //开机充电使能
|
||
u8 charge_full_V; //充满电电压大小
|
||
u8 charge_full_mA; //充满电电流大小
|
||
u8 charge_mA; //充电电流大小
|
||
u8 charge_trickle_mA; //涓流充电电流大小
|
||
u8 ldo5v_pulldown_en; //下拉使能位
|
||
u8 ldo5v_pulldown_lvl; //ldo5v的下拉电阻配置项,若充电舱需要更大的负载才能检测到插入时，请将该变量置为对应阻值
|
||
u8 ldo5v_pulldown_keep; //下拉电阻在softoff时是否保持,ldo5v_pulldown_en=1时有效
|
||
u16 ldo5v_off_filter; //ldo5v拔出过滤值，过滤时间 = (filter*2 + 20)ms,ldoin<0.6V且时间大于过滤时间才认为拔出,对于充满直接从5V掉到0V的充电仓，该值必须设置成0，对于充满由5V先掉到0V之后再升压到xV的充电仓，需要根据实际情况设置该值大小
|
||
u16 ldo5v_on_filter; //ldo5v>vbat插入过滤值,电压的过滤时间 = (filter*2)ms
|
||
u16 ldo5v_keep_filter; //1V<ldo5v<vbat维持电压过滤值,过滤时间= (filter*2)ms
|
||
};
|
||
|
||
#define CHARGE_PLATFORM_DATA_BEGIN(data) \
|
||
struct charge_platform_data data = {
|
||
|
||
#define CHARGE_PLATFORM_DATA_END() \
|
||
};
|
||
|
||
|
||
enum {
|
||
CHARGE_FULL_33V = 0, //充满标记位
|
||
TERMA_33V, //模拟测试信号
|
||
VBGOK_33V, //模拟测试信号
|
||
CICHARGE_33V, //涓流转恒流信号
|
||
};
|
||
|
||
enum {
|
||
CHARGE_EVENT_CHARGE_START,
|
||
CHARGE_EVENT_CHARGE_CLOSE,
|
||
CHARGE_EVENT_CHARGE_FULL,
|
||
CHARGE_EVENT_LDO5V_KEEP,
|
||
CHARGE_EVENT_LDO5V_IN,
|
||
CHARGE_EVENT_LDO5V_OFF,
|
||
CHARGE_EVENT_USB_CHARGE_IN,
|
||
CHARGE_EVENT_USB_CHARGE_OFF,
|
||
};
|
||
|
||
|
||
extern void set_charge_event_flag(u8 flag);
|
||
extern void set_charge_online_flag(u8 flag);
|
||
extern u8 get_charge_online_flag(void);
|
||
extern u8 get_charge_poweron_en(void);
|
||
extern void charge_start(void);
|
||
extern void charge_close(void);
|
||
extern u8 get_charge_mA_config(void);
|
||
extern void set_charge_mA(u8 charge_mA);
|
||
extern u8 get_ldo5v_pulldown_en(void);
|
||
extern u8 get_ldo5v_pulldown_res(void);
|
||
extern u8 get_ldo5v_online_hw(void);
|
||
extern u8 get_lvcmp_det(void);
|
||
extern void charge_check_and_set_pinr(u8 mode);
|
||
extern u16 get_charge_full_value(void);
|
||
extern void charge_module_stop(void);
|
||
extern void charge_module_restart(void);
|
||
extern const struct device_operations charge_dev_ops;
|
||
extern void charge_set_ldo5v_detect_stop(u8 stop);
|
||
|
||
#endif //_CHARGE_H_
|