460 lines
14 KiB
C
460 lines
14 KiB
C
#include "app_config.h"
|
||
|
||
#ifdef CONFIG_BOARD_AC6369C_DEMO
|
||
|
||
#include "system/includes.h"
|
||
#include "asm/charge.h"
|
||
#include "device/key_driver.h"
|
||
#include "asm/power/p33.h"
|
||
#include "asm/pwm_led.h"
|
||
|
||
#define LOG_TAG_CONST BOARD
|
||
#define LOG_TAG "[BOARD]"
|
||
#define LOG_ERROR_ENABLE
|
||
#define LOG_DEBUG_ENABLE
|
||
#define LOG_INFO_ENABLE
|
||
/* #define LOG_DUMP_ENABLE */
|
||
#define LOG_CLI_ENABLE
|
||
#include "debug.h"
|
||
|
||
void board_power_init(void);
|
||
/************************** LOW POWER config ****************************/
|
||
const struct low_power_param power_param = {
|
||
.config = TCFG_LOWPOWER_LOWPOWER_SEL, //0：sniff时芯片不进入低功耗 1：sniff时芯片进入powerdown
|
||
.btosc_hz = TCFG_CLOCK_OSC_HZ, //外接晶振频率
|
||
.delay_us = TCFG_CLOCK_SYS_HZ / 1000000L, //提供给低功耗模块的延时(不需要需修改)
|
||
.btosc_disable = TCFG_LOWPOWER_BTOSC_DISABLE, //进入低功耗时BTOSC是否保持
|
||
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //强VDDIO等级,可选：2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.6V
|
||
.vddiow_lev = TCFG_LOWPOWER_VDDIOW_LEVEL, //弱VDDIO等级,可选：2.1V 2.4V 2.8V 3.2V
|
||
.osc_type = OSC_TYPE_LRC,
|
||
.dcdc_port = TCFG_DCDC_PORT_SEL,
|
||
};
|
||
|
||
|
||
/************************** KEY MSG****************************/
|
||
/*各个按键的消息设置，如果USER_CFG中设置了USE_CONFIG_KEY_SETTING为1，则会从配置文件读取对应的配置来填充改结构体*/
|
||
u8 key_table[KEY_NUM_MAX][KEY_EVENT_MAX] = {
|
||
// SHORT LONG HOLD UP DOUBLE TRIPLE
|
||
};
|
||
|
||
|
||
// *INDENT-OFF*
|
||
/************************** UART config****************************/
|
||
#if TCFG_UART0_ENABLE
|
||
UART0_PLATFORM_DATA_BEGIN(uart0_data)
|
||
.tx_pin = TCFG_UART0_TX_PORT, //串口打印TX引脚选择
|
||
.rx_pin = TCFG_UART0_RX_PORT, //串口打印RX引脚选择
|
||
.baudrate = TCFG_UART0_BAUDRATE, //串口波特率
|
||
|
||
.flags = UART_DEBUG, //串口用来打印需要把改参数设置为UART_DEBUG
|
||
UART0_PLATFORM_DATA_END()
|
||
#endif //TCFG_UART0_ENABLE
|
||
|
||
/************************** CHARGE config****************************/
|
||
#if TCFG_CHARGE_ENABLE
|
||
CHARGE_PLATFORM_DATA_BEGIN(charge_data)
|
||
.charge_en = TCFG_CHARGE_ENABLE, //内置充电使能
|
||
.charge_poweron_en = TCFG_CHARGE_POWERON_ENABLE, //是否支持充电开机
|
||
.charge_full_V = TCFG_CHARGE_FULL_V, //充电截止电压
|
||
.charge_full_mA = TCFG_CHARGE_FULL_MA, //充电截止电流
|
||
.charge_mA = TCFG_CHARGE_MA, //充电电流
|
||
/*ldo5v拔出过滤值，过滤时间 = (filter*2 + 20)ms,ldoin<0.6V且时间大于过滤时间才认为拔出
|
||
对于充满直接从5V掉到0V的充电仓，该值必须设置成0，对于充满由5V先掉到0V之后再升压到xV的
|
||
充电仓，需要根据实际情况设置该值大小*/
|
||
.ldo5v_off_filter = 100,
|
||
/*ldo5v的10k下拉电阻使能,若充电舱需要更大的负载才能检测到插入时，请将该变量置1,默认值设置为1
|
||
对于充电舱需要按键升压,且维持电压是从充电舱经过上拉电阻到充电口的舱，请将该值改为0*/
|
||
.ldo5v_pulldown_en = 0,
|
||
CHARGE_PLATFORM_DATA_END()
|
||
#endif//TCFG_CHARGE_ENABLE
|
||
|
||
/************************** AD KEY ****************************/
|
||
#if TCFG_ADKEY_ENABLE
|
||
const struct adkey_platform_data adkey_data = {
|
||
.enable = TCFG_ADKEY_ENABLE, //AD按键使能
|
||
.adkey_pin = TCFG_ADKEY_PORT, //AD按键对应引脚
|
||
.ad_channel = TCFG_ADKEY_AD_CHANNEL, //AD通道值
|
||
.extern_up_en = TCFG_ADKEY_EXTERN_UP_ENABLE, //是否使用外接上拉电阻
|
||
.ad_value = { //根据电阻算出来的电压值
|
||
TCFG_ADKEY_VOLTAGE0,
|
||
TCFG_ADKEY_VOLTAGE1,
|
||
TCFG_ADKEY_VOLTAGE2,
|
||
TCFG_ADKEY_VOLTAGE3,
|
||
TCFG_ADKEY_VOLTAGE4,
|
||
TCFG_ADKEY_VOLTAGE5,
|
||
TCFG_ADKEY_VOLTAGE6,
|
||
TCFG_ADKEY_VOLTAGE7,
|
||
TCFG_ADKEY_VOLTAGE8,
|
||
TCFG_ADKEY_VOLTAGE9,
|
||
},
|
||
.key_value = { //AD按键各个按键的键值
|
||
TCFG_ADKEY_VALUE0,
|
||
TCFG_ADKEY_VALUE1,
|
||
TCFG_ADKEY_VALUE2,
|
||
TCFG_ADKEY_VALUE3,
|
||
TCFG_ADKEY_VALUE4,
|
||
TCFG_ADKEY_VALUE5,
|
||
TCFG_ADKEY_VALUE6,
|
||
TCFG_ADKEY_VALUE7,
|
||
TCFG_ADKEY_VALUE8,
|
||
TCFG_ADKEY_VALUE9,
|
||
},
|
||
};
|
||
#endif
|
||
|
||
/************************** IO KEY ****************************/
|
||
#if TCFG_IOKEY_ENABLE
|
||
const struct iokey_port iokey_list[] = {
|
||
{
|
||
.connect_way = TCFG_IOKEY_POWER_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_POWER_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 0, //按键值
|
||
},
|
||
|
||
#if(!TCFG_UART0_ENABLE || TCFG_UART0_TX_PORT != IO_PORT_DP)
|
||
{
|
||
.connect_way = TCFG_IOKEY_PREV_CONNECT_WAY,
|
||
.key_type.one_io.port = TCFG_IOKEY_PREV_ONE_PORT,
|
||
.key_value = 1,
|
||
},
|
||
#endif
|
||
|
||
{
|
||
.connect_way = TCFG_IOKEY_NEXT_CONNECT_WAY,
|
||
.key_type.one_io.port = TCFG_IOKEY_NEXT_ONE_PORT,
|
||
.key_value = 2,
|
||
},
|
||
};
|
||
const struct iokey_platform_data iokey_data = {
|
||
.enable = TCFG_IOKEY_ENABLE, //是否使能IO按键
|
||
.num = ARRAY_SIZE(iokey_list), //IO按键的个数
|
||
.port = iokey_list, //IO按键参数表
|
||
};
|
||
|
||
#if MULT_KEY_ENABLE
|
||
//组合按键消息映射表
|
||
//配置注意事项:单个按键按键值需要按照顺序编号,如power:0, prev:1, next:2
|
||
//bit_value = BIT(0) | BIT(1) 指按键值为0和按键值为1的两个按键被同时按下,
|
||
//remap_value = 3指当这两个按键被同时按下后重新映射的按键值;
|
||
const struct key_remap iokey_remap_table[] = {
|
||
{.bit_value = BIT(0) | BIT(1), .remap_value = 3},
|
||
{.bit_value = BIT(0) | BIT(2), .remap_value = 4},
|
||
{.bit_value = BIT(1) | BIT(2), .remap_value = 5},
|
||
};
|
||
|
||
const struct key_remap_data iokey_remap_data = {
|
||
.remap_num = ARRAY_SIZE(iokey_remap_table),
|
||
.table = iokey_remap_table,
|
||
};
|
||
#endif
|
||
|
||
#endif
|
||
|
||
|
||
void debug_uart_init(const struct uart_platform_data *data)
|
||
{
|
||
#if TCFG_UART0_ENABLE
|
||
if (data) {
|
||
uart_init(data);
|
||
} else {
|
||
uart_init(&uart0_data);
|
||
}
|
||
#endif
|
||
}
|
||
|
||
/************************** PWM_LED ****************************/
|
||
#if TCFG_PWMLED_ENABLE
|
||
LED_PLATFORM_DATA_BEGIN(pwm_led_data)
|
||
.io_mode = TCFG_PWMLED_IOMODE, //推灯模式设置:支持单个IO推两个灯和两个IO推两个灯
|
||
.io_cfg.one_io.pin = TCFG_PWMLED_PIN, //单个IO推两个灯的IO口配置
|
||
LED_PLATFORM_DATA_END()
|
||
#endif
|
||
|
||
|
||
|
||
static void board_devices_init(void)
|
||
{
|
||
#if TCFG_PWMLED_ENABLE
|
||
pwm_led_init(&pwm_led_data);
|
||
#endif
|
||
|
||
#if (TCFG_IOKEY_ENABLE || TCFG_ADKEY_ENABLE || TCFG_TOUCH_KEY_ENABLE)
|
||
key_driver_init();
|
||
#endif
|
||
}
|
||
|
||
extern void cfg_file_parse(u8 idx);
|
||
void board_init()
|
||
{
|
||
board_power_init();
|
||
adc_vbg_init();
|
||
adc_init();
|
||
cfg_file_parse(0);
|
||
|
||
devices_init();
|
||
|
||
board_devices_init();
|
||
|
||
#if TCFG_CHARGE_ENABLE
|
||
extern int charge_init(const struct dev_node *node, void *arg);
|
||
charge_init(NULL, (void *)&charge_data);
|
||
#if TCFG_HANDSHAKE_ENABLE
|
||
if(get_charge_online_flag()){
|
||
handshake_app_start(0, NULL);
|
||
}
|
||
#endif
|
||
#else
|
||
/*close FAST CHARGE */
|
||
CHARGE_EN(0);
|
||
CHGBG_EN(0);
|
||
#endif
|
||
|
||
log_info("board_init");
|
||
//必须在切换到dcdc前设置好
|
||
if(get_charge_online_flag()){
|
||
log_info("charge...select LDO15");
|
||
power_set_mode(PWR_LDO15);
|
||
}else{
|
||
power_set_mode(TCFG_LOWPOWER_POWER_SEL);
|
||
}
|
||
}
|
||
enum {
|
||
PORTA_GROUP = 0,
|
||
PORTB_GROUP,
|
||
PORTC_GROUP,
|
||
};
|
||
|
||
static void port_protect(u16 *port_group, u32 port_num)
|
||
{
|
||
if (port_num == NO_CONFIG_PORT) {
|
||
return;
|
||
}
|
||
port_group[port_num / IO_GROUP_NUM] &= ~BIT(port_num % IO_GROUP_NUM);
|
||
}
|
||
|
||
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
|
||
static void close_gpio(void)
|
||
{
|
||
u16 port_group[] = {
|
||
[PORTA_GROUP] = 0xffff,
|
||
[PORTB_GROUP] = 0xffff,
|
||
[PORTC_GROUP] = 0xffff,
|
||
};
|
||
|
||
#if TCFG_ADKEY_ENABLE
|
||
port_protect(port_group,TCFG_ADKEY_PORT);
|
||
#endif
|
||
|
||
#if TCFG_IOKEY_ENABLE
|
||
port_protect(port_group, TCFG_IOKEY_POWER_ONE_PORT);
|
||
port_protect(port_group, TCFG_IOKEY_PREV_ONE_PORT);
|
||
port_protect(port_group, TCFG_IOKEY_NEXT_ONE_PORT);
|
||
#endif /* TCFG_IOKEY_ENABLE */
|
||
|
||
#if TCFG_CHARGE_ENABLE && TCFG_HANDSHAKE_ENABLE
|
||
if (is_softoff == 0) {
|
||
port_protect(port_group, TCFG_HANDSHAKE_IO_DATA1);
|
||
port_protect(port_group, TCFG_HANDSHAKE_IO_DATA2);
|
||
}
|
||
#endif
|
||
|
||
//< close gpio
|
||
gpio_dir(GPIOA, 0, 16, port_group[PORTA_GROUP], GPIO_OR);
|
||
gpio_set_pu(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
|
||
gpio_set_pd(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
|
||
gpio_die(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
|
||
gpio_dieh(GPIOA, 0, 16, ~port_group[PORTA_GROUP], GPIO_AND);
|
||
|
||
gpio_dir(GPIOB, 0, 16, port_group[PORTB_GROUP], GPIO_OR);
|
||
gpio_set_pu(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
|
||
gpio_set_pd(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
|
||
gpio_die(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
|
||
gpio_dieh(GPIOB, 0, 16, ~port_group[PORTB_GROUP], GPIO_AND);
|
||
|
||
|
||
gpio_dir(GPIOC, 0, 16, port_group[PORTC_GROUP], GPIO_OR);
|
||
gpio_set_pu(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
|
||
gpio_set_pd(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
|
||
gpio_die(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
|
||
gpio_dieh(GPIOC, 0, 16, ~port_group[PORTC_GROUP], GPIO_AND);
|
||
|
||
//< close usb io
|
||
usb_iomode(1);
|
||
|
||
//dp dm is io_key
|
||
/* gpio_set_pull_up(IO_PORT_DP, 0); */
|
||
/* gpio_set_pull_down(IO_PORT_DP, 0); */
|
||
/* gpio_set_direction(IO_PORT_DP, 1); */
|
||
/* gpio_set_die(IO_PORT_DP, 0); */
|
||
/* gpio_set_dieh(IO_PORT_DP, 0); */
|
||
|
||
/* gpio_set_pull_up(IO_PORT_DM, 0); */
|
||
/* gpio_set_pull_down(IO_PORT_DM, 0); */
|
||
/* gpio_set_direction(IO_PORT_DM, 1); */
|
||
/* gpio_set_die(IO_PORT_DM, 0); */
|
||
/* gpio_set_dieh(IO_PORT_DM, 0); */
|
||
|
||
/* printf("JL_USB_IO->CON0=0x%x\r\n", JL_USB_IO->CON0); */
|
||
/* printf("JL_USB_IO->CON1=0x%x\r\n", JL_USB_IO->CON1); */
|
||
/* printf("JL_USB->CON0=0x%x\r\n", JL_USB->CON0); */
|
||
/* */
|
||
/* printf("JL_USB1_IO->CON0=0x%x\r\n", JL_USB1_IO->CON0); */
|
||
/* printf("JL_USB1_IO->CON1=0x%x\r\n", JL_USB1_IO->CON1); */
|
||
/* printf("JL_USB1->CON0=0x%x\r\n", JL_USB1->CON0); */
|
||
}
|
||
|
||
/************************** PWR config ****************************/
|
||
struct port_wakeup port0 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.attribute = BLUETOOTH_RESUME, //保留参数
|
||
.iomap = IO_PORTB_01, //唤醒口选择
|
||
.filter_enable = ENABLE,
|
||
};
|
||
|
||
const struct sub_wakeup sub_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
const struct charge_wakeup charge_wkup = {
|
||
.attribute = BLUETOOTH_RESUME,
|
||
};
|
||
|
||
const struct wakeup_param wk_param = {
|
||
.filter = PORT_FLT_2ms,
|
||
.port[1] = &port0,
|
||
.sub = &sub_wkup,
|
||
.charge = &charge_wkup,
|
||
};
|
||
|
||
//-----------------------------------------------
|
||
|
||
|
||
static void keep_set_io_output(int io_sel,int en)
|
||
{
|
||
gpio_set_pull_up(io_sel, 0);
|
||
gpio_set_pull_down(io_sel, 0);
|
||
gpio_set_direction(io_sel, 0);
|
||
gpio_set_die(io_sel, 1);
|
||
gpio_set_output_value(io_sel, en);
|
||
}
|
||
|
||
static void keep_set_io_input(int io_sel,u8 pull_up_en,u8 pull_down_en)
|
||
{
|
||
gpio_set_pull_up(io_sel, pull_up_en);
|
||
gpio_set_pull_down(io_sel, pull_down_en);
|
||
gpio_set_direction(io_sel, 1);
|
||
gpio_set_die(io_sel, 0);
|
||
}
|
||
|
||
|
||
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
|
||
extern void dac_power_off(void);
|
||
void board_set_soft_poweroff(void)
|
||
{
|
||
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15){
|
||
power_set_mode(PWR_LDO15);
|
||
}
|
||
|
||
close_gpio();
|
||
|
||
gpio_set_pull_up(IO_PORT_DP, 0);
|
||
gpio_set_pull_down(IO_PORT_DP, 0);
|
||
gpio_set_direction(IO_PORT_DP, 1);
|
||
gpio_set_die(IO_PORT_DP, 0);
|
||
gpio_set_dieh(IO_PORT_DP, 0);
|
||
|
||
gpio_set_pull_up(IO_PORT_DM, 0);
|
||
gpio_set_pull_down(IO_PORT_DM, 0);
|
||
gpio_set_direction(IO_PORT_DM, 1);
|
||
gpio_set_die(IO_PORT_DM, 0);
|
||
gpio_set_dieh(IO_PORT_DM, 0);
|
||
|
||
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15
|
||
&& TCFG_DCDC_PORT_SEL != NO_CONFIG_PORT){
|
||
//need keep dcdc's io output 0
|
||
keep_set_io_output(TCFG_DCDC_PORT_SEL,0);
|
||
}
|
||
|
||
}
|
||
|
||
#define APP_IO_DEBUG_0(i,x) //{JL_PORT##i->DIR &= ~BIT(x), JL_PORT##i->OUT &= ~BIT(x);}
|
||
#define APP_IO_DEBUG_1(i,x) //{JL_PORT##i->DIR &= ~BIT(x), JL_PORT##i->OUT |= BIT(x);}
|
||
|
||
|
||
//-----------------------------------------------
|
||
void sleep_exit_callback(u32 usec)
|
||
{
|
||
putchar('>');
|
||
APP_IO_DEBUG_1(A, 6);
|
||
|
||
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15){
|
||
/* putchar('}'); */
|
||
power_set_mode(TCFG_LOWPOWER_POWER_SEL);
|
||
}
|
||
|
||
}
|
||
|
||
void sleep_enter_callback(u8 step)
|
||
{
|
||
/* 此函数禁止添加打印 */
|
||
if (step == 1) {
|
||
putchar('<');
|
||
APP_IO_DEBUG_0(A, 6);
|
||
/*dac_power_off();*/
|
||
if(TCFG_LOWPOWER_POWER_SEL == PWR_DCDC15){
|
||
/* putchar('{'); */
|
||
power_set_mode(PWR_LDO15);
|
||
}
|
||
} else {
|
||
|
||
close_gpio();
|
||
|
||
gpio_set_pull_up(IO_PORTA_03, 0);
|
||
gpio_set_pull_down(IO_PORTA_03, 0);
|
||
gpio_set_direction(IO_PORTA_03, 1);
|
||
|
||
usb_iomode(1);
|
||
|
||
gpio_set_pull_up(IO_PORT_DP, 0);
|
||
gpio_set_pull_down(IO_PORT_DP, 0);
|
||
gpio_set_direction(IO_PORT_DP, 1);
|
||
gpio_set_die(IO_PORT_DP, 0);
|
||
|
||
gpio_set_pull_up(IO_PORT_DM, 0);
|
||
gpio_set_pull_down(IO_PORT_DM, 0);
|
||
gpio_set_direction(IO_PORT_DM, 1);
|
||
gpio_set_die(IO_PORT_DM, 0);
|
||
}
|
||
}
|
||
|
||
|
||
//-----------------------------------------------
|
||
|
||
|
||
void board_power_init(void)
|
||
{
|
||
log_info("Power init : %s", __FILE__);
|
||
|
||
//< close short key reset
|
||
/* p33_and_1byte(P3_PR_PWR, ~BIT(3)); */
|
||
//< close long key reset
|
||
/* p33_and_1byte(P3_PINR_CON, 0); */
|
||
|
||
power_init(&power_param);
|
||
|
||
/*sdpg_config(1);*/
|
||
|
||
power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff);
|
||
|
||
power_keep_dacvdd_en(0);
|
||
|
||
power_wakeup_init(&wk_param);
|
||
|
||
|
||
/* #if (!TCFG_IOKEY_ENABLE && !TCFG_ADKEY_ENABLE) */
|
||
/* charge_check_and_set_pinr(0); */
|
||
/* #endif */
|
||
}
|
||
#endif
|